Course details

Concrete and masonry work carries some of the most severe hazards on any construction site: collapsing formwork, unbraced masonry walls, impalement on protruding rebar, and the caustic effects of wet cement on skin. These incidents are preventable, and prevention starts with knowing the rules and the reasons behind them. This online course delivers the safety knowledge required by OSHA's construction standard for concrete and masonry, 29 CFR 1926 Subpart Q.

The training addresses a direct need for contractors and crews: OSHA holds employers responsible for protecting workers from the specific hazards of concrete and masonry construction, and workers who understand Subpart Q make fewer costly, dangerous mistakes. Delivered online, the course lets your team learn the standard without leaving the trailer or the classroom, then apply it on the pour, the wall, and the lift.

The payoff is a crew that recognizes a strike-by or caught-in hazard before it becomes an incident, and a company with the documentation to prove it trained them.

This course is an informational and awareness-based training resource, developed and reviewed by an OSHA subject matter expert to ensure content accuracy and regulatory alignment. However, completion of this course does not qualify as OSHA Outreach Training under the OSHA Outreach Training Program, nor does it qualify you as a Competent Person as defined under any OSHA standard.

By the end, you will not just check a compliance box. You will understand exactly how these pathogens spread, how to prevent exposure, and what to do in the critical minutes after contact occurs.

---

Course Overview

Scope and General Requirements of Subpart Q

Understand what 29 CFR 1926 Subpart Q covers and the general requirements that apply across concrete and masonry operations. This section sets the framework for every task on site.

Equipment, Tools, and Load Placement

Learn the safe use of concrete equipment and tools, correct load placement, and the hazards of moving and positioning heavy materials.

Cast-in-Place Concrete and Formwork

Explore the requirements for cast-in-place concrete and the formwork and shoring that must support it. Formwork failure is catastrophic, and this section explains how to prevent it.

Precast Concrete and Lift-Slab Operations

Understand the specific precautions for precast components and lift-slab construction, two operations where a single control failure can drop a load on a crew.

Masonry Construction and Limited Access Zones

Learn the requirements for masonry construction, including the limited access zone that must be established alongside a wall under construction and the bracing that prevents wall collapse.

Impalement, Post-Tensioning, and Struck-By Hazards

Review protection against impalement on rebar, the dangers of post-tensioning operations, and the struck-by and caught-in hazards that dominate concrete and masonry incident data.

Chemical and Skin Hazards of Cement

Understand why wet concrete and Portland cement are hazardous to skin and eyes, and the practical controls that prevent chemical burns and long-term damage.

Who Should Take This Course?

This course is designed for anyone involved in concrete and masonry construction, including:

• Concrete finishers, form setters, and laborers
• Masons and bricklayers
• Construction supervisors, foremen, and superintendents
• Site safety officers and competent persons
• General contractors and subcontractors
• Apprentices and workers new to concrete and masonry operations
• Employers responsible for Subpart Q compliance and worker training

Key Benefits

• Prevent the site's most severe incidents. Wall collapses, formwork failures, and impalements are catastrophic and preventable. This course targets them.
• Put Subpart Q into plain language. Workers learn what the standard requires and, just as important, why, so the rules stick.
• Support inspection readiness. Documented, standard-aligned training strengthens your compliance record.
• Train the crew online. Deliver consistent safety knowledge without pulling the team off the project.
• Earn a certificate. Demonstrate completion to general contractors, clients, and regulators.

Why Enroll in This Course?

In concrete and masonry work, the difference between a normal day and a fatality is often a single control that someone forgot or never understood. This course closes that gap by teaching the Subpart Q requirements in a practical, jobsite-focused way that crews actually retain. You get clear instruction on the hazards that cause the most serious injuries, guidance you can apply on the next pour or wall, and a certificate that documents your training. Employers get a workforce that understands limited access zones, formwork risks, and cement hazards, plus a training record that supports Subpart Q compliance. On projects where safety performance wins bids and prevents shutdowns, that is a direct return on a small investment.